Powder Tile Adhesive
Non-Slip Tile Adhesive Powder
Conforms to BS 5980: 1980 Type 1 Class AA

PRODUCT DESCRIPTION

Non-Slip Tile Adhesive Powder is a thin-bed cementitious non-slip ceramic tile adhesive.

The adhesive is characterised by its excellent adhesion to many construction materials such as concrete, cement rendering, asbestos cement, unglazed tile and gypsum based finishes. Non-Slip Tile Adhesive Powder is easy to use as it only requires appropriate amount of water to produce a creamy easy-to-trowel adhesive.

For areas subjecting to extreme vibration or where high water resistance is required, Flextoner (please refer to separate data sheet) can be incorporated into the mix, as this will greatly improve the resilience to vibration and its waterproofing property.

TYPICAL PROPERTIES

  • Easy to use
  • Non-slip property enables tiling to commence top-down.
  • Excellent bond and shear strengths.
  • Good open and adjustability time.
  • Can be incorporated with Flextoner to give excellent waterproofing property and high resilient to vibration.
Click Links Below For Our Products
Cementone Cemgrout GPA
Cementone Cemgrout NS
Cementone Prufe-it
Cementone Superplasticiser EB821-R
Marlease
Cementone No. 2
Cempatch -118
Cementone Paveseal
Mortar Clean
Superbond SBR
Powder Tile Adhesive
Expagate Standard
Cemplas
Conret
Expagate Spray
Superplastticiser EB 821-P
Cemcure EB 286 Clear
Cemcure EB 286 White
Cemcure EB 559 Clear
Cemcure EB 559 White
Conspeed
Cementone Hardflor-NOM Coloured
Cementone Hardflor-NOM
Cementone Hardflor-NM
Cementone Hardflor-NM Coloured

APPLICATION PROCEDURES

  • Surface Preparation
  1. The surface should clean and free of loose, flaky materials, oil, grease and other contaminants.
  2. All surface defects must be made good.
  3. New cement-based substrate must be allowed to cured for at least 28 days.
  4. High absorbent surface, such as heated surface from exposure to sunlight, must be damped with clean water.
  • Preparation of Mix
  1. Pour the required proportion of water into a pail, in the ratio of 6.0 - 6.5 litres of water to 25 kg of powder adhesive.
  2. Add the proportioned amount of adhesive and mix thoroughly using a power mixer until a homogenous lump-free smooth paste is achieved.
  • Application of Mix
  1. Apply mixed adhesive by working it thoroughly onto the surface using a notched trowel.
  2. However when incorporating with Flextoner to improve waterproofing property, a continuous solid bedding should be employed.
  3. Apply only enough adhesive that can be tiled in 15 minutes as prolong exposure of bare adhesive may affect some of its properties.
  4. Pressed tiles firmly onto wet adhesive and ensure good contact.
  5. Should skinning be formed due to prolong exposure before tiling, re-trowel the skinned surface until 'wet adhesive is formed to receive tiles.
  6. Any adjustment to tile's position must be made within 15 minutes after fixing of tile otherwise the applied adhesive need to be removed and re-applied.
  7. Tiled surfaces must be protected against direct sunlight, rain and traffic for at least 24 hours.
  8. Allow adhesive to set for at least 24 hours before grouting.

Note : Do not wet surface of applied adhesive after skinning occurs.

Unicorp Sendirian Berhad Lot 66, Beribi II Industrial Estate,
B.S.B. BE1118 P.O. Box 620, Bandar Seri Begawan BS8671,
Brunei Darussalam
Tel: 673-245 0450, 245 0500, 245 0998
Fax: 673-245 0999 E-mail: unicorp@brunet.bn or unicorpbrunei@brunet.bn
Copyright Unicorp Sendirian Berhad All Rights Reserved 2005

to set for at least 24 hours before grouting.

Note : Do not wet surface of applied adhesive after skinning occurs.

Unicorp Sendirian Berhad Lot 66, Beribi II Industrial Estate,
B.S.B. BE1118 P.O. Box 620, Bandar Seri Begawan BS8671,
Brunei Darussalam
Tel: 673-245 0450, 245 0500, 245 0998
Fax: 673-245 0999 E-mail: unicorp@brunet.bn or unicorpbrunei@brunet.bn
Copyright Unicorp Sendirian Berhad All Rights Reserved 2005